Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

高分影像辅助下的航空高光谱严密几何检校方法

 惯性测量单元(IMU)与传感器视准轴的偏心角和偏心矢量是造成航空线阵列高光谱数据几何校正误差的主要原因之一。在分析偏心角与偏心矢量误差来源之后提出该误差由IMU主轴与传感器主轴的角度偏差、测区固定偏差、GPS中心与传感器投影中心相对偏差组成,在此基础上建立了较为严密的检校模型。针对模型解算时需要大量高精度控制点的问题,提出了一种高分影像辅助下的亚像元精度控制点自动提取方法。通过多地区、多传感器高光谱航测实验表明,亚像元精度控制点能有效提高模型解算精度。新检校模型可获得亚像元校正精度,推扫式传感器——应用型机载成像光谱仪(AISA)建模中误差约为0.39个像元,摆扫式传感器——实用型模块化成像光谱仪(OMIS)建模中误差约为0.23个像元,校正后的影像可直接进行拼接。     

带轴对称台阶的圆锥高超声速边界层转捩试验

在Ma 6风洞内，通过高频脉动压力测试技术和基于纳米粒子示踪的平面激光散射(NPLS)技术，分别对带前向、后向轴对称台阶的圆锥高超声速边界层转捩进行了试验研究。采用功率谱密度分析和互相关计算等方法对脉动压力数据进行分析，得到了边界层中扰动波的发展规律，定量分析了第二模态波的相关参数。结果显示：两种模型中第二模态波在沿流向向下游发展的过程中，其幅值均先增大再衰减、特征频率均逐渐减小；特征频率和传播速度整体上均随雷诺数的增大而增加(后台阶模型中特征频率由100 kHz增至196 kHz，前台阶中则由 97 kHz 增至174 kHz)、波长变化规律则与之相反(后台阶中由6.35 mm降至4.54 mm，前台阶由7.35 mm降至 4.66 mm )；后台阶模型中第二模态波初次出现位置比前台阶中更靠近上游，边界层转捩位置较前台阶前移。将NPLS结果与高频脉动压力测试结果进行对比，两者吻合较好。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

大涵道比风扇/增压级进气畸变数值模拟研究

为探究进口总压畸变下大涵道比风扇/增压级内部流场的主要特征，基于三维彻体力模型的思想，开发了一套能够实现风扇/增压级内外涵联算功能的三维数值计算程序。利用该程序模拟了某大涵道比风扇/增压级在周向总压畸变进气下的三维流场。计算结果表明：大涵道比风扇单转子不同叶高处的畸变传递特征差异较大，转子出口总压畸变强度由叶根到叶尖逐渐降低，在叶尖处衰减为最小值1.5%；在转子出口相应诱导出的总温畸变强度由叶根到叶尖逐渐升高，在叶尖处达到最大值1.4%；进口周向总压畸变导致风扇转子总压比下降0.5%，而风扇转子出口形成的总压总温复合畸变导致增压级总压比下降2%；总压畸变在增压级中呈逐级衰减趋势，而高温畸变区的周向范围在逐级增加。     

一种高动态低信噪比卫星导航信号捕获方法

为提升高动态低信噪比环境下卫星导航信号的捕获性能,提出了一种基于分数阶傅里叶变换(FrFT)及部分匹配滤波(PMF)的捕获方法。在该方法中,接收机首先利用PMF对接收信号做分段相干积分,随后借助快速傅里叶变换(FFT)对分段积分结果做离散快速FrFT,最后通过检测FrFT输出的峰值完成信号的捕获。由于具有多普勒频率变化率的卫星导航信号在FrFT后呈现能量聚焦特性,所提方法能够显著提高信号的长时间相干积分增益。同时对所提算法的捕获概率、平均捕获时间以及算法复杂度等性能指标进行了理论分析及计算机仿真验证。仿真表明,与传统的PMF-FFT方法相比,所提方法能够通过延长相干积分时间的方式有效提升高动态低信噪比卫星导航信号的捕获概率、降低捕获时间。     

基于反问题的涡轮过渡流道一体化支板设计方法

为进一步改善大涵道比涡扇发动机气动性能及燃油经济性,降低其污染物排放,控制其重量与成本,提出了一种高效的高、低压涡轮过渡流道整流支板一体化设计理念,即对原型支板与第一级低压涡轮导叶进行初步正问题一体化设计,并基于气流角全三维粘性反问题进行进一步改型设计,使得在保证自身气动性能不降低的基础上,带一体化支板涡轮过渡流道能够与高、低压涡轮实现良好匹配。以某型发动机过渡流道为算例开展了一体化设计工作,并采用三维数值模拟方法进行了设计点、非设计点流场分析评估。结果表明,设计点工况下一体化支板出口气流角以及马赫数分布均与原型导叶出口一致,验证了一体化设计的有效性。同时,带一体化支板的过渡流道总压损失从原型流道的2.49%降低到了1.02%。而在非设计工况,带一体化支板的过渡流道气流分离明显减小,具有更宽的最佳工况范围。     

A robust object-based shadow detection method for cloud-free high resolution satellite images over urban areas and water bodies

Unwanted contrast in high resolution satellite images such as shadow areas directly affects the result of further processing in urban remote sensing images. Detecting and finding the precise position of shadows is critical in different remote sensing processing chains such as change detection, image classification and digital elevation model generation from stereo images. The spectral similarity between shadow areas, water bodies, and some dark asphalt roads makes the development of robust shadow detection algorithms challenging. In addition, most of the existing methods work on pixel-level and neglect the contextual information contained in neighboring pixels. In this paper, a new object-based shadow detection framework is introduced. In the proposed method a pixel-level shadow mask is built by extending established thresholding methods with a new C₄ index which enables to solve the ambiguity of shadow and water bodies. Then the pixel-based results are further processed in an object-based majority analysis to detect the final shadow objects. Four different high resolution satellite images are used to validate this new approach. The result shows the superiority of the proposed method over some state-of-the-art shadow detection method with an average of 96% in F-measure.     

RNSS/INS深耦合高动态导航接收机测试方法研究CSCD

卫星导航和惯性导航采用深耦合方式实现导航作为世界上最先进的导航形式,在国防中的应用越来越广泛,但其在高动态下的性能需要验证。当前针对深耦合高动态下导航接收机的测试研究较少,本文介绍了基于卫星信号模拟器的测试系统组成及测试用高动态场景,运用模拟测试原理,通过对导航接收机在高动态下定位速度和跟踪灵敏度的测试及其结果分析,验证了导航接收机的深耦合功能,对此类接收机的测试方法进行了初步探究。     

提高数字器件频率稳定度测量分辨率的研究

提出了一种利用信号时空关系测量相位差来修正差拍周期的方法,并通过实验证明了该方法的正确性和可行性。此方法在提高数字器件频率稳定度测量分辨率方面还有很大的空间,是一种很有潜力的高精度测量技术。